Search Results

Three techniques for the measurement of the oxides of nitrogen in automotive exhaust were evaluated. These included a “nitrous fume” analyzer, a gaseous NO2 colorimeter, and a movable mass spectrometer. All data obtained were compared to data from currently accepted wet chemical methods, the phenoldisulfonic acid and the “modified” Saltzman. Of the techniques evaluated, the mass spectrometer analysis of NO has been found to be the most useful for the study of nitrogen oxides in engine exhaust. The high cost of wet chemical analysis has indicated a need for an improved and continuous analytical method. The mass spectrometer approach measures NO within seconds of its discharge, thus minimizing any reactions prior to measurement.

The design requirements for the frame as a load carrying member are discussed in relationship to a highway truck and its basic vehicle package. The theoretical and experimental procedures are given in detail to demonstrate the techniques for frame design. The features of a method to laboratory test a frame with correlation to service miles is discussed.

In 1962 and 1964 the Coordinating Research Council (CRC) evaluated the vapor locking characteristics of about 40 selected new model cars during centralized programs at Yuma, Arizona. Volatility tolerances were determined during acceleration following a hot soak at approximately 100 F ambient using two reference fuel series with diverse front-end volatilities. Fifty per cent of the 1962 model cars tested had a limiting vapor pressure equal to or less than 8.4 lb with the high volatility fuels and 9.7 lb with the low volatility fuels. Comparable values in the 1964 program were 8.9 lb for the high and 10.4 lb for the low volatility fuels. Analytical results obtained on vehicle tank samples for the first time during 1964 showed that limiting temperature at a given vapor-to-liquid ratio also was a useful parameter in defining car volatility tolerances.

Discussion of four factors pertinent to any overall ride evaluation. These factors are frame beaming, fifth wheel location, special body mountings, and variable loading conditions on tandem truck and tractor ride. The methodology for measuring the characteristics of these factors is reviewed and practical solutions for improved ride are given.

Most automobiles, at certain speeds with at least one window open, develop a pulsating pressure which is felt mainly through the ears and is objectionable to the occupants. While this “aerodynamic wind throb” is noticeable over a range of speeds, there is a fairly pronounced peak in the effect at one speed. This problem is studied analytically and experimentally. It is established that the car is a dynamic system consisting of a Helmholtz resonator excited by an edge tone. It is shown that the trouble can be corrected by changing the natural frequency, minimizing or eliminating the excitation, or increasing damping of the system.

The presentation here of a computer program simulating an engine cycle emphasizes mechanical factors under the control of the engine designer rather than scientific aspects of combustion. Data secured by measuring valves, manifolds, and other parts on a flow bench are used to calculate instantaneous flow in and out of the cylinder for the firing engine. Heat transfer, finite time of combustion, and variable specific heat of the gas are also calculated. The program is particularly well adapted to indicating the direction and relative magnitude of the effect of changing one variable, such as valve size, at a time.

In 1958 the Coordinating Research Council conducted an extensive series of vapor lock road tests at a centralized location to study the effect of test variables on the hot fuel handling characteristics of passenger cars. Two years later, another test program was carried out at a common location to determine the hot fuel handling characteristics of a selected group of 1960 cars, employing the vapor lock survey technique developed in the 1958 program. The results obtained from the two programs indicate that this technique provides a satisfactory basis for defining the more severe vapor handling characteristics of automobiles in a relatively short time.

Investigations of the non-flame oxidation of exhaust gas hydrocarbons and carbon monoxide are reported. These investigations cover basic studies of the relationship of temperature, oxygen, and residence time to oxidation rates with external, supplementary, exhaust gas heating. Reaction (oxidation) is then shown to be possible without supplementary heat in the test installation of a homogeneous reactor on one cylinder of a V-8 engine on an engine dynamometer. Vehicle tests were then conducted to determine the operational characteristics and oxidation performances of a series of multi-cylinder reactors mounted on 292-cubic-inch-displacement engines. Unique methods of air introduction and heat conservation are described. These reactors were capable of effectively decreasing exhaust concentrations of hydrocarbon and carbon monoxide while the vehicles were driven over a traffic route. Tests of two reactors designed especially for fast warm-up are reported.

THE METHOD of validating proving ground test routines as a sample of customer operations is described. Comparisons of field survey and proving ground failure statistics are analyzed to establish sample reliability and severity ratios. Alternative means of accelerating the test program are considered, with examples indicating the effect on correlation. Use of proving ground routes as a link in establishing laboratory test to customer service correlation is treated. Procedures and instrumentation for developing load cycle information on the road, and programming random load cycles into laboratory test fixtures for simulated service life testing are discussed with some examples of applications to automotive components. In the performance test area, several performance parameters representative of customer requirements are developed. Techniques of improving comparative evaluations by eliminating the effect of extraneous variables such as the driver and the weather are presented.

THE Free-Piston Engine Program described in this paper was concerned with determining thermodynamic relationships of small, high-speed engines. The purpose was to establish proper engine geometry and mechanical design which could then be applied to developing larger automotive engines. The author outlines the problems encountered during the Program's beginnings: starting system, powerplant assembly, cooling system, and lubrication. The results indicated that the free-piston engine would be particularly applicable to the farm tractor. The author thinks that such a powerplant may equal or better the diesel engine in economy.

RUMBLE is a low-frequency noise heard in high compression engines and accompanied by high rates of pressure rise. Thus, rumble indicates a rapid combustion process. This paper describes a method of studying this problem: by detection of flame fronts by ionization gaps. Results of experiments show that rumble is caused by deposit ignition in the end-gas region. These multiple ignitions occur after the normal flame front has progressed partially across the chamber. The authors conclude that this type of deposit ignition is generally a self-sustaining process, lasting until the deposits are burned out at a particular engine performance level. When the level is increased, the process repeats itself.

THIS paper describes the development and utilization of a new Ford free-piston power-plant, the model 519. Mr. Noren traces the development of the engine from the initial idea to the point where commercial utilization could be considered. Mr. Erwin describes one commercial use: in the Typhoon tractor. The ratio of size and weight to horsepower is favorable for farm tractors, being smaller and lighter than equivalent diesel engines. The performance of the tractor has been satisfactory thus far, operating smoothly and being practically vibration-free, with little noise. The advantages of the free-piston gasifier, as reported by the authors, are: flexibility, fuel economy, no need for auxiliary starting engine, economical manufacture of a wide range of engine sizes, adaptability to a wide range of fuels, and good torque characteristics.

HUMAN perception thresholds to motions and the various characteristics of motions in six degrees of freedom are presented. Experiments made to establish these thresholds for disturbances of the duration or frequency that might arise from highway geometry—durations in the range of from one second to several hundred seconds—are described. Applications of motion sensitivity criteria in the design of vertical and horizontal highway curves and transitions are developed, with examples from company proving grounds in Arizona and Michigan. The resulting geometric features of the high-speed road systems differ in several important respects from conventional highway practice and previous automotive test-track designs.

APPLICATIONS of nuclear energy in automotive manufacture have been made principally in the field of radioactivity. These are grouped under the following categories: radiography, nondestructive testing, gaging and control, tracer techniques, and static neutralizers. Radioactivity techniques are being used in foundry operations to check stock and metal levels in cupolas and distribution of element additives. In steel operations, these techniques are being used to check assimilation of ore-concentrate fines and thickness of rolled sheet steel. Other applications include measurement of pipe and wall thickness in pressure lines and engines, and inspection of castings and welds for internal faults. Radioactive techniques for improving processes, quality, and materials have potentially universal application. Greater industrial access to reactors will permit broader study and speed the development of new applications of radio-activity in industry.

THE study of engine life, carried out by investigating engine wear in typical service, and by then striving to find the most effective ways of controlling it, forms the basis of this paper on contaminants in lubricants. The investigation involved a study of engine wear in 20,000 miles of operation typical of the average driver. The average driver was selected by using test cars from an employee transportation car pool. At the conclusion of the tests it was found that the use of the full-flow oil filter proved to be the best method for restricting engine wear caused by contaminants that get inside the engine. It was also shown that after successfully eliminating large, solid particles, further restriction of engine wear would depend upon the ability of the oil to lubricate, and upon the engine design to provide the oil supply in a manner suitable for lubrication of each part of the engine.

NODULAR cast iron, so called because the graphite is present as finely dispersed, well-rounded particles, is made in two stages: The first stage consists of the addition of magnesium or other carbide formers, which promote the formation of white iron in one normally solidifying gray. In the second stage a ferrosilicon type of inoculant overcomes the tendency toward white iron and causes the graphite to precipitate out in the form of small spherulites. The methods of making nodular iron, the effect of composition on physical properties, economic factors involved, and potential applications are discussed in this paper.

PROPER protection of metal parts operating as bearing surfaces, or in contact under relatively heavy loads, during the break-in period often means the difference between successful operation and failure. Various surface coatings have been investigated to discover which ones will give this protection. The authors discuss here three types of surface treatment for cast-iron and steel that do give superior wear and scuff resistance.